These laser parameters have been tested mostly with our ComMarker laser engraver, but they can also be applied to other power laser sources in the market. Understand that the result on your material can be different from the result shown in the Photos. That happens for various factors such as other material components, different power laser source quality, a different lens, etc.
These laser parameters have been tested mostly with our ComMarker laser engraver, but they can also be applied to other power laser sources in the market.
Understand that the result on your material can be different from the result shown in the Photos. That happens for various factors such as other material components, different power laser source quality, a different lens, etc.
Machine: B4 20w
Software: Ezcad2
Engraving pass:
~33 passes (x hatched 45 degrees)
Speed 666
88-90% power
20Khz
0.04 line space
Clean up pass:
4 passes (x hatched 45 degrees)
1000 speed
40% power
60Khz
0.1 line space
Black pass
~2 or 3mm defocused
~1-2 passes
50.80 speed
52.5 power
25khz
1st hatch is 45 degrees spaced at 0.0254
2nd hatch is the same but -45 degrees
Software Lightburn
Machine ComMarker B4
Laser Module Output Power 20W
Material Used Stainless steel
Material Info 1mm
Making Time(mins) 15mins
Setting:
Process Method Filling/picture
Process Material Stainless steel
Speed(mm/s) 300
Max Power(%) 50
Pass 1
Line space 0.054
Frequency 25
Machine：B4 20W
200mm lens refocused 3mm
Software：Lightburn
speed： 750
power： 60
frequency： 80khz
Lines per inch：0 .02
2 passes
Machine: B6-30w
Software: LightBurn
1st pass：
Power:50%
Speed:500mm/s
Frequèncy:20kHz
2nd pass：
Power:45%
Speed:500mm/s
Frequèncy:35kHz
Clean up pass：
Power:40%
Speed:3500mm/s
Frequèncy:20kHz
Machine：B4 30W
110mm lens with correct focus
Software：lightburn
speed:1000
power: 90
frequency：50khz
Lines per inch： 0.02
Angle：45
400 passes
Image mode:3d sliced
Then finishing
Speed: 2000
Power: 30
Frequency: 100
Lines per inch：0.05
Angle：45
Machine: B6-30w
Software: LightBurn
Power:80%
Speed:1000mm/s
Frequèncy:20kHz
Pulse width:200ns
Line interval:0.0254mm
Image mode:3d sliced
Passes:200
Processing time:2.5hrs
Machine：B4 30W
200mm lens as a fill
Software：lightburn
speed:1500
power: 50
frequency：20khz
Lines per inch： 0.025
Angle：45
Machine: B6 30w
Software: LightBurn
Power:80%
Speed:1000mm/s
Frequency:20kHz
Line interval:0.0254mm
Image mode. 3d sliced
Passes:200
Processing time:2.5 hrs
Basic information:
Software Ezcad
Machine ComMarker B4 20w
Laser Module Output Power 20W
Material Used Acrylic
Material Info 3mm
Making Time(s) 36
For filling only:
Process Method picture
Process Material Acrylic
Speed(mm/s) 500
Max Power(%) 50
Pass 1
Machine: B6 30w
Software: LightBurn
Power:10%
Speed:1000mm/s
Frequency:20kHz
Pulse width: 200ns
Line interval:0.01mm
Passes:10
Processing time:1.5 hrs
Machine: B6 30w
Software: LightBurn
Engrave:Power:80%
Speed:1000mm/s
Frequèncy: 30kHz
Pulse width: 200ns
Line interval:0.01mm
Passes:8
Cleaning Pass:
Speed:1500mm/s
Power:20%
Line space: 0.01
Frequency: 100
Pass: 2
Machine: B6-30w
Software: LightBurn
Power:10%
Speed:2000mm/s
Frequency:30kHz
Line interval:0.0254mm
Image mode: Jarvis
Processing time:5 min
MMachine: B6 60w-mopa
Software: LightBurn
Power:95%
Speed:700mm/s
Frequency:35kHz
Line interval:0.01mm
Continue Engraving
Machine: B4 60w-mopa
Software: LightBurn
Making pass:
Speed:1000mm/s
Power:100%
Line space: 0.05
Q-pulse: 200
Frequency: 40
Pass: 4
Cleaning Pass:
Speed:1500mm/s
Power:20%
Line space: 0.01
Q-pulse: 200
Frequency: 100
Pass: 2
Settings:
ComMarker B4 60W (1mm Brass Cutting, 110×110 Lens):
• Power: 100%
• Speed: 25
• Frequency: 30
• Q-Pulse Width: 400
• Passes: 30
ComMarker Omni 1 (Wood Cutting, 115×115 Lens):
• Speed: 50
• Frequency: 30
• Q-Pulse Width: 1
• Passes: 6
| SPEED | POWER | INTERVAL | Q-PAULSE | FREQ | |
| Black | 850 | 55 | 0.03 | 10 | 233 |
| RED | 500 | 15 | 0.003 | 50 | 300 |
| YELLOW | 750 | 50 | 0.005 | 10 | 200 |
| SKIN | 1500 | 30 | 0.05 | 200 | 20 |
| WHITE | 750 | 30 | 0.003 | 10 | 250 |
REAL TIME COST: 6.42mins
MACHINE TYPE: ComMarker b4-60W-MOPA
FIELD LENS:150MM
| SPEED | POWER | INTERVAL | Q-PAULSE | FREQ | |
| Black | 850 | 55 | 0.03 | 10 | 233 |
| RED | 500 | 15 | 0.003 | 50 | 300 |
| Blue | 950 | 50 | 0.005 | 10 | 200 |
| SKIN | 1500 | 30 | 0.05 | 200 | 20 |
| WHITE | 750 | 30 | 0.003 | 10 | 250 |
REAL TIME COST: 5.05mins
MACHINE TYPE: ComMarker b4-60W-MOPA
FIELD LENS:150MM
| SPEED | POWER | INTERVAL | Q-PAULSE | FREQ | |
| Black | 850 | 55 | 0.03 | 10 | 233 |
| RED | 500 | 15 | 0.003 | 50 | 300 |
| YELLOW | 750 | 50 | 0.005 | 10 | 200 |
| SKIN | 1500 | 30 | 0.05 | 200 | 20 |
| WHITE | 750 | 30 | 0.003 | 10 | 250 |
REAL TIME COST: 10.40mins
MACHINE TYPE: ComMarker b4-60W-MOPA
FIELD LENS:150MM
Basic information:
Software： EZCAD2
Machine： ComMarker B4 20W
Laser Power： 20W
Material Used： BRASS
Material Info： COIN
Making Time(mins)： 23MINS
Setting:
Speed(mm/s)： 1000
Frequency(Khz)： 30
Max Power(%)： 90
Pass： 157
Line space： 0.02
Dot width：
Hatch Mode：
Q Pulse Width (nm)：only for mopa machines
Basic information:
Software： LightBurn
Machine： ComMarker B4 60W-mopa
Laser Power：620W
Material Used：BRASS
Material Info： COIN
Making Time(mins)： 6hr50mins
Engraving Setting:
Speed(mm/s)： 2000
Frequency(Khz)： 100
Max Power(%)： 90
Pass： 512
Line space： 0.025
Dot width：
Hatch Mode： 45°
Q Pulse Width (nm)：only for mopa machines 200
Clean Setting:
Speed(mm/s)： 2500
Frequency(Khz)： 200
Max Power(%)： 90
Pass： 1
Line space： 0.015
Dot width：
Hatch Mode： 45°
Q Pulse Width (nm)：only for mopa machines 200
Machine:ComMarker B6 60w Mopa
Software: LightBurn
Mode:3D Slice
Speed: 1000
Pass Count: 512
Interval: 0.025
Q-Pulse: 120ns
Power: 90%
Freq: 40kHz
Cleanup:
Speed: 6000
Interval: .1
Frequency: 75
Q-Pulse: 200ns
Power: 30%
Clean after 10 passes
Basic information:
Software EZCAD
Machine ComMarker B4 Mopa Fiber Laser Marking Machine
Laser Module Output Power 60W
Material Used ID card
Material Info ID card
Making Time(mins) 3min
Setting:
Process Method ID card
Process Material ID card
Speed(mm/s) 2000
Max Power(%) 40
Pass 1
Line space 0.03
Basic information:
Software EZCAD
Machine ComMarker B4 Mopa Fiber Laser
Laser Module Output Power 60W
Material Used Rusted coin
Material Info Rusted coin
Making Time(mins) 3 mins
Setting:
For filling only:
Process Method Hatching
Process Material Rusted coin
Speed(mm/s) 1000
Max Power(%) 90
Pass Depends on how rusted the material is
Line space 0.05
Basic information:
Software EZCAD
Machine ComMarker B4 Mopa Laser Engraving Machine
Laser Module Output Power 60W
Material Used
Battery,aluminum sheet
Material Info
Battery,aluminum sheet
Making Time(s) 30S
Setting:
Process Method Laser Welding
Process Material
Battery,aluminum sheet
Speed(mm/s) 25
Max Power(%) 100
Frequency(KHz) 100
Pass 1
Machine: B4 60w-mopa
Software: ezcad2
Power:100%
Speed:500mm/s
Frequency:30kHz
Pulse width: 10ns
Line interval:0.01mm
Machine: B4 60w-mopa
Software: ezcad2
Speed:2000mm/s
Power:30%
Line space: 0.045
Q-pulse: 200
Frequency: 30
Pass: 1
Speed:2000
Power:50%
Interval:0.05
Q-Pulse:200
Freq:30
Image mode: Threshold
Software: LightBurn
Machine: ComMarker B4-60w mopa
Machine: B6 60w-mopa
Software: LightBurn
Power:85%
Speed:200mm/s
Frequency:30kHz
Pulse width: 200ns
Line interval:0.01mm
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:40,
Q-pulse: 1,
Speed: 1000
pass: 1
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:40,
Q-pulse: 1,
Speed: 500
pass: 1
Line Interval:0.03
Image mode:Atkinson
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:40,
Q-pulse: 1,
Speed: 200
pass: 1
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:40,
Q-pulse: 1,
Speed: 200
pass: 1
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:30,
Q-pulse: 1,
Speed: 500
pass: 1
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn
Marking pass
Freq.:30,
Q-pulse: 20
Speed: 1000
pass: 1
Line Interval:0.03
cutting pass
Freq.:40,
Q-pulse: 1
Speed: 100
pass: 5
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:40,
Q-pulse: 1,
Speed: 75,
pass: 10
Settings:
ComMarker B4 60W (1mm Brass Cutting, 110×110 Lens):
• Power: 100%
• Speed: 25
• Frequency: 30
• Q-Pulse Width: 400
• Passes: 30
ComMarker Omni 1 (Wood Cutting, 115×115 Lens):
• Speed: 50
• Frequency: 30
• Q-Pulse Width: 1
• Passes: 6
Machine: Omni 1 (UV 5W)
Software: LightBurn
ComMarker B4 60W (1mm Brass Cutting, 110×110 Lens):
Power: 100%
Speed: 50
Frequency: 30
Q-Pulse Width: 200
Passes: 80
ComMarker Omni 1 (Engraving, 115×115 Lens):
Speed: 200
Frequency: 30
Q-Pulse Width: 1
Passes: 3
Cross Hatch & Flood Fill Enabled
ComMarker Omni 1 (Cutting, 115×115 Lens):
Speed: 50
Frequency: 30
Q-Pulse Width: 1
Passes: 6
Machine: Omni 1 (UV 5W)
Software: LightBurn
Speed: 200
Frequency: 40
Q-Pulse: 1
Passes: 35
Took about 40 seconds
Machine: Omni 1 (UV 5W)
Software: LightBurn
Speed: 100
Frequency: 40
Q-Pulse: 15
Passes: 1
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:40,
Q-pulse: 15
Speed: 1000
pass: 1
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn-Rotary Marking
Freq.:40,
Q-pulse: 5,
Speed: 600,
pass: 2
Rotary setting:
Split size:0.1mm
overlap:0.1mm
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:30
Q-pulse: 17
Speed: 2500
pass: 1
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:40,
Q-pulse: 1,
Speed: 100
pass: 3-5
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:40,
Q-pulse: 1,
Speed: 833.3
pass: 1
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn
Freq.:30,
Q-pulse: 20
Speed:1000
pass: 1
Line Interval:0.03
Machine: Omni 1 (UV 5W)
Software: LightBurn
Speed: 1000
Frequency: 40
Q-Pulse: 1
Passes: 1
